Since

HVAC Licensing

Exam Prep

The*“Guide to Passing the HVAC Licensing Exam”* will have you prepared to take the exam for less than one half the cost of a classroom cram course. Learn the Mechanical Code, the Fuel Gas Code, plus, Business and Law, Manuals J, D and N.

Download and check out a sample of our course —————>

The*“Guide to Passing the HVAC Licensing Exam”* will have you prepared to take the exam for less than one half the cost of a classroom cram course. Learn the Mechanical Code, the Fuel Gas Code, plus, Business and Law, Manuals J, D and N.

This copyrighted HVAC licensing exam prep course teaches and explains the provisions of the Mechanical Code, Fuel Gas Code. Manuals J and N load calculations, Manual D duct design and business principles. it is designed to assist you in understanding the tough stuff; the stuff many examinees struggle with on the exam.

**WHAT YOU WILL LEARN WITH OUR GUIDE**

** Mechanical Code**– What to highlight and how to calculate ventilation and combustion air requirements, hood sizes and return air ducts, plus more

updated through 2020

✔** Fuel Gas Code**– What to highlight. Determining confined spaces, gas pipe sizes, vent sizes and clearances, plus more

✔ ** Manual J, 8th edition-** We have reduced this manual from 627 pages to just 11 pages as an easy to understand procedure for calculating loads . Basic principles of heat transfer and thermodynamics. Operating cost calculations

✔ **Manual D**– “Three easy steps to duct sizing.”

✔ **Manual N**– Once you get through Manual J, N will be a cakewalk.

✔ **Symbols and Psychrometrics** – How to read and use charts and calculate A/C capacity

✔ **Business-** Learn business equations and accounting principles. Find out how to figure profit the correct way.

✔ ** Energy Code**– What you need to know to pass.

✔ ** 150 Strategic Practice Questions**– With answers and how we got’em

Don’t know where to begin?

Our course will guide you right through.

Our course is based on the International Codes. Most states have adopted the International Codes, although they may bare the name of a state, such as *New York State Mechanical Code* or *North Carolina Mechanical Code*.

Typical exam questions

1. Where the minimum size combustion air duct is 6” X 12”, a metal lover with unknown free area, must be at least _______ square inches

2. Calculate the required outdoor ventilation rate for a 1700 sq. ft. office space?

3. When installing B-vent for a 120,000 BTUH gas furnace (fan assisted), what is the minimum diameter if the vent is 12 feet high with a 2 foot lateral?

4. Calculate the velocity (FPM) of 800 CFM in an 8″ x 14″ duct.

5. If R-19 insulation is added to a 1200 square foot ceiling with a U-value of .05, what is the new R-value? New U-value? Heat loss at 50 degree temperature difference?

6. If you purchase an appliance for $1000 and wish to make 30% profit; what would your selling price be? Hint: the answer is not $130

**Answers**

1. 96

2. 144.5 cfm

3. 5”

4. 1039 fpm

5. R=39, U=.025, 1500 btuh

6. $1428.57

States colored in pink have adopted the International Mechanical and Fuel Gas Codes. Our course will definitely help you.

Think about it!

After spending hours in a cram course, listening to an instructor rushing through the provisions of all the code books, plus teaching you how to perform load calculations and size ducts, vents and piping and then covering business and accounting principles, the average attendee will come out of the class with one question on his mind; “What did he say?”

*Most of us have been there before.**The Guide is simply the best way to go.*

We make learning easy.

Once you’ve read our sections on Manual J (load calculations) and Manual D (duct design) you’ll be looking for a butt kicking machine for not ordering our course earlier. There is simply no easier method for fully understanding these manuals. For example, the Guide condenses Manual J from 627 pages down to 11 pages; Now, that’s making it easy

Because many states are now adding business questions to their HVAC exams, we have included a section on business practices and math. It is written in a language, we in the trade understand. You no longer have to have the skills of a Philadelphia lawyer, mathematician and a CPA to help prepare for the exam.

AN EXCERPT FROM THE GUIDE TAKEN FROM OUR SECTION ON MANUAL J (load calculations)

**R-Value**

This is a number indicating the ability of a substance to resist the flow of heat. The higher the R value, the better it acts as an insulator.

Typical R-values of building components can be found in Manual J or go to: http://www.coloradoenergy.org/procorner/stuff/r-values.htm for a free listing of R-values.**U value**

(Learn and understand U value. It is the foundation of a load calculation.)

The U value is the number of BTUs that pass though one square foot of substance in one hour’s time when there is one degree temperature difference. The U value is the reciprocal* of the R value. A U-value can to said to be the rate of conduction**U=1/R**

*A reciprocal of a number is 1 divided by the number. The reciprocal of 20 is 1/20 or .05.

Suppose you had a six-inch thick, R- 19 fiberglass insulation batt, and you wanted to know how much heat will pass through it. First, determine the U value.**U= 1/R****U= 1/19****U=.0526**

Therefore, .0526 BTUs pass through 1 square foot of the batt each hour when there is one degree temperature difference.

If the batt measured 2’ x 8’ we would have a total area of 16 sq. ft. We could then say that .8414 BTUs (16 sq. ft. x .0526 BTUs). Pass through the entire batt in one hour when there is one degree temperature difference.

Carrying our example just one step further, if the temperature on one side of the batt is 20 degrees and on the other side it is 70 degrees, then we would have a 50-degree temperature difference (70–20). Therefore, 42.08 BTU’s (.8414 BTU’s x 50 degrees) would pass through the batt in one hour.

Simply stated, use the following formula to determine the amount of heat gained or lost through any substance:**BTUH = U x TD X AREA**

=.0526 x 50 X 16′

= 42.08

Once you know the U value, the square footage and the temperature difference, you can calculate the BTU heat loss or gain per hour through a substance. However, walls, floors and ceilings are not made up of just insulation. A wall may be made up of brick, sheathing, insulation and sheetrock, each of which has its own R value. The R value of each component must be added together to obtain the total R value. Then we simply take the reciprocal (1/R) and get the total U value of the wall. For a list of R-values, locate a table titled “R Values of Common Building Materials” in Manual J8, or go to:

http://www.coloradoenergy.org/procorner/stuff/r-values.htm

AN EXCERPT FROM THE GUIDE TAKEN FROM OUR SECTION ON THE FUEL GAS CODE

Single** appliance -Table 504.2(1) Sizing vents**

*What size B vent is needed for a 160,000 BTUH, naturally ventilated appliance if the total vent height is 18’ and the lateral 2’?*

Under the height column you have to choose either 15’ or 20’. Remember this: The taller the vent the more capacity it has, therefore, if the 20’ row is used the vent may be under sized.* Always use the shorter height.*

In this case use 15’. Now use the 2’ lateral and select a vent size under NAT. A 5” vent will handle only 150,000 BTUH, while a 6” vent will handle 225,000 BTUH, therefore select a 6” vent.

See? You already learned something!

Pricing and ordering information.

## No need to wait for the mailman

## The “*Guide to Passing the HVAC Exam”* May be instantly downloaded to your computer as soon as your payment is verified, or, you may order a hardcopy and allow 3-5 days for delivery

## All credit or debit cards are accepted.

Purchase Hardcopy NOW

“Guide to Passing the HVAC Licensing Exam”

**To order our course, simply click on the BUY NOW button. Your course will arrive in 3-5 business days via USPS priority mail. Your payment will be safely processed by our trusted partner, ***PayPal.*

Only $189

Don’t have a Paypal account?

No Problem, simply select”Pay with credit card” on the paypal order form

OR—–>

Save $42 by ordering the instant download.

“So easy, your dog would pass.”

Save $42 by ordering the instant download

Need the course now?

Save $42

Don’t wait for the mailman, Order the Instant download and get it now

As soon as your payment is verified, you will receive download instructions on your computer screen. You may save the course to your computer or print it out (Approx. 140 pages). Your payment will be processed by our trusted partner, **Clickbank***

Instant Download

**Only $147**

*ClickBank is the retailer of products on this site. CLICKBANK® is a registered trademark of Click Sales, Inc., a Delaware corporation located at 1444 S. Entertainment Ave., Suite 410 Boise, ID 83709, USA and used by permission. ClickBank’s role as retailer does not constitute an endorsement, approval or review of these products or any claim, statement or opinion used in promotion of these products.*

**ENERGY MARKETING SERVICE**

**ENERGY MARKETING SERVICE**

**Have questions ?**

Contact us anytime by email

energymarketingservice@gmail.com

252-943-1028 (M-F, 9am – 6pm,

Eastern)

STATE-BY-STATE HVAC LICENSING BOARDS

**Select a state below to go to the respective HVAC licensing board**

Colorado x

Hawaii x

Illinois x

Indiana x

Kansas x

Maine x

Missouri x

New Hampshire x

New York (Local)

Pennsylvania x

South Dakota x

Vermont x

Wyoming

X – NO STATE LICENSE REQUIRED

**Back to “Guide to Passing the HVAC Exam”Back to “Guide to Passing the HVAC Exam****“**